NVT has a full range of CCTV video transmission products featuring Screw Terminal and screwless termination. These products were specifically designed for CCTV market installers who desire to install UTP structured cabling systems and stop using coax.
- Adaptive StubEQ™ fully automatic 2-band equalization provides adjustment-free equalization every time
- Adaptive DigitalEQ™ fully automatic 4-band equalization provides adjustment-free equalization every time
Passive Transceivers (Single Channel)
- Full-motion CCTV video at distances up to 225m when used with any passive NVT transceiver or hub
- Up to 1km with a NVT DigitalEQ™ hub or active receiver
- Up to 460m with a NVT StubEQ™ hub
- Male BNC allows connection directly to the camera or DVR
- Reliable Screwless UTP terminal connection
- No power required
- Exceptional interference rejection
- Frequency Response DC to 10 MHz
- Built-in transient protection
- Supports “up-the-coax” type control signal up to 225m
- Full-motion CCTV video at distances up to 225m when used with any passive NVT transceiver or hub
- Up to 1km with a NVT DigitalEQ™ hub or active receiver
- Up to 460m with a NVT StubEQ™ hub
- Male BNC allows connection directly to the camera or DVR
- Reliable Screwless UTP terminal connection
- No power required
- Exceptional interference rejection
- Frequency Response DC to 10 MHz
- Built-in transient protection
- Supports “up-the-coax” type control signal up to 225m
Order number: EMNV1040 NVT NV-208A-M Single Channel Video Passive Transceiver
Order number: EMNV1041 NVT NV-214A-M Single Channel Video Passive TransceiverActive Receivers (Single Channel)
The NVT Model NV-652R Video Receiver is an active (amplified) device that allows the transmission of real-time monochrome or color video on up to 1 mile (1,6km) using Category 2 or better Unshielded Twisted-Pair (UTP) telephone wire.
The unparalleled interference rejection and low emissions of the Model NV-652R allow long run video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground potential differences exist. With built-in transient protection, damaging voltage spike problems are eliminated. The built-in sharpness and brightness controls compensate for cable loss.
- Full-motion CCTV video at distances up to 3,000ft (1km) when used with any passive NVT transceiver; 1 mile (1,6km) when used with NV-653T transmitter
- Exceptional interference rejection
- Frequency Response DC to 10 MHz
- Built-in transient protection and ground lifting
- Built-in brightness and sharpness controls; blue power LED, green active LED
- Compatible with qualified UTP cameras
- Up to ten NV-652Rs may be rack mounted using the NV-RM8/10 rack panel kit
- Best choice for DVR and high resolution applications over 750ft (225m)
- Limited lifetime warranty
Order number: EMNV1030 NVT NV-652R Active receiver
Order number: EMNV1014 NVT NV-RM810 Rack Panel for 10 NV-652R or NV-653T -devicesActive Transmitters (Single Channel)
The NVT Model NV-653T Video Transmitter is an active (amplified) device that allows the transmission of real-time monochrome or color video on up to one mile (1,6km) using Category-2 or better Unshielded Twisted-Pair (UTP) telephone wire.
The unparalleled interference rejection and low emissions of the Model NV-653T allows long run video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground potential differences exist. With built-in transient protection, damaging voltage spike problems are eliminated.
- Full-motion CCTV video at distances up to 1 mile (1,6km) when used with active NVT receiver or hub
- Exceptional interference rejection
- Frequency Response DC to 10 MHz
- Built-in transient protection and ground lifting
- Three-position distance range switch
- Blue power LED, green active LED
- Up to ten NV-653Ts may be rack mounted using the NV-RM8/10 Rack Panel Kit
- Limited lifetime warranty
Order number: EMNV1031 NVT NV-653T Video Active Transmitter
Order number: EMNV1014 NVT NV-RM8/10 Rack Panel for 10 NV-652R or NV-653T -devices8-Channel Active ReceiversEmploying NVT’s latest generation StubEQ™ technology, the NV-842 is an 8-channel active (amplified) hub that allows the transmission of full-motion monochrome or color video for distances up to 2,000ft (600m) using Category 2 or better unshielded twisted-pair (UTP) wire. The receiver hub continuously and automatically conditions the video signal, compensating for cable attenuation, ground loops, and voltage transients, independent of video signal content.
The unparalleled interference rejection and low emissions allow long run video to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground-potential differences exist. With built-in transient protection, damaging voltage spikes are eliminated.
- Adaptive StubEQ™ fully automatic 2-band equalization provides adjustment-free equalization every time
- Compact rack-mountable 19″ 1U high enclosure features 8 channels
- Full motion CCTV video at distances up to 1,500ft (460m) when used with any passive NVT transceiver or hub; 2,000ft (600m) when used with the NV-653T active transmitter
- RJ45 connectivity with optional NV-RJ45A RJ45-to-screw-terminal adaptors (included)
- Exceptional interference rejection
- Built-in transient protection and ground-lifting
- Compatible with qualified UTP cameras
- Includes rack mount hardware and two NV-RJ45A adaptors
- Limited lifetime warranty
Employing NVT‘s latest generation Digital EQ™ technology, the NV-872 is an 8-channel active (amplified) hub that allows the transmission of full-motion monochrome or color video for distances up to 1 mile (1,6km) using Category 2 or better unshielded twisted-pair (UTP) wire. The receiver hub continuously and automatically conditions the video signal, compensating for cable attenuation, wiring polarity, ground loops, and voltage transients, independent of video signal content.
The unparalleled interference rejection and low emissions allow long run video to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground-potential differences exist. With built-in transient protection, damaging voltage spikes are eliminated.
- Adaptive DigitalEQ™ fully automatic 4-band equalization continuously provides adjustment-free equalization
- Compact rack-mountable 19″ 1U high enclosure features 8 channels with 4 outputs per channel
- Full motion CCTV video at distances up to 3,000ft (1km) when used with any passive NVT transceiver or hub; 1 mile (1,6km) when used with the NV-653T active transmitter; 1,000ft (300m) with shielded twisted-pair when used with any passive NVT transceiver or hub
- RJ45 connectivity with optional NV-RJ45A RJ45-to-screw-terminal adaptors (included)
- Exceptional interference rejection
- Built-in transient protection and ground-lifting
- Frequency Response DC to 10 MHz
- Automatic compensation for reverse-polarity wiring
- At-a-glance per-channel diagnostics
- Compatible with qualified UTP cameras
- Includes eight 2ft (60cm) coax jumper cables, rack mount hardware and two NV-RJ45A adaptors
Order number: xxxx xxxx NVT NV-842 8 Channel StubEQ™ Active Receiver Hub
Order number: xxxx xxxx NVT NV-872 8-Channel Digital EQ™ Active Receiver DA Hub16-Channel Active Receivers
Employing NVT’s latest generation StubEQ™ technology, the NV-1642 is a 16-channel active (amplified) hub that allows the transmission of real time monochrome or color video for distances up to 2,000ft (600m2,) using Category 5 or better unshielded twisted-pair (UTP) wire. The receiver hub continuously and automatically conditions the video signal, compensating for cable attenuation, ground loops, and voltage transients, independent of video signal content.
The unparalleled interference rejection and low emissions allow long run video to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. this allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground-potential differences exist. With built-in transient protection, damaging voltage spikes are eliminated.
- Adaptive StubEQ™ fully automatic 2-band equalization provides adjustment-free equalization every time
- Compact rack-mountable 19″ 1U high enclosure features 16 channels
- Full motion CCTV video at distances up to 1,500ft (460m) when used with any passive NVT transceiver or hub; 2,000ft (600m) when used with the NV-653T active transmitter
- RJ45 connectivity with optional NV-RJ45A RJ45-to-screw-terminal adaptors (included)
- Exceptional interference rejection
- Built-in transient protection and ground-lifting
- Compatible with qualified UTP cameras
- Includes rack mount hardware and four NV-RJ45A adaptors
- Limited lifetime warranty
Employing NVT‘s latest generation DigitalEQ™ technology, the NV-1672 is an 16-channel active (amplified) hub that allows the transmission of full-motion monochrome or color video for distances up to 1 mile (1,6km) using Category 2 or better unshielded twisted-pair (UTP) wire. The receiver hub continuously and automatically conditions the video signal, compensating for cable attenuation, wiring polarity, ground loops, and voltage transients, independent of video signal content.
The unparalleled interference rejection and low emissions allow long run video to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground-potential differences exist. With built-in transient protection, damaging voltage spikes are eliminated.
- Adaptive DigitalEQ™ fully automatic 4-band equalization provides adjustment-free equalization every time
- Compact rack-mountable 19″ 1U high enclosure features 16 channels with 2 outputs per channel
- Full motion CCTV video at distances up to 3,000ft (1km) when used with any passive NVT transceiver or hub; 1 mile (1,6km) when used with the NV-653T active transmitter; 1,000ft (300m) with shielded twisted-pair when used with any passive NVT transceiver or hub
- RJ45 connectivity with optional NV-RJ45A RJ45-to-screw-terminal adaptors (included)
- Exceptional interference rejection
- Built-in transient protection and ground-lifting
- Frequency Response DC to 10 MHz
- Automatic compensation for reverse-polarity wiring
- At-a-glance per-channel diagnostics
- Compatible with qualified UTP cameras
- Includes four 2ft (60cm) coax jumper cables, rack mount hardware and four NV-RJ45A adaptors
Order number: EMNVxxxx NVT NV-1642 16-Channel StubEQ™ Active Receiver Hub
Order number: EMNVxxxx NVT NV-1672 16-Channel DigitalEQ™ Active Receiver DA Hub
32-Channel Active ReceiversEmploying NVT’s latest generation StubEQ™ technology, the NV-3242 is a 32-channel active (amplified) hub that allows the transmission of full-motion monochrome or color video for distances up to 2,000ft (600m) using Category 2 or better unshielded twisted-pair (UTP) wire. The receiver hub continuously and automatically conditions the video signal, compensating for cable attenuation, ground loops, and voltage transients, independent of video signal content. The unparalleled interference rejection and low emissions allow long run video to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. this allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground-potential differences exist. With built-in transient protection, damaging voltage spikes are eliminated.
- Adaptive StubEQ™ fully automatic 2-band equalization provides adjustment-free equalization every time
- Compact rack-mountable 19″ 1U high enclosure features 32 channels
- Full motion CCTV video at distances up to 1,500ft (460km) when used with any passive NVT transceiver or hub; 2,000ft (600m) when used with the NV-653T active transmitter
- RJ45 connectivity with optional NV-RJ45A RJ45-to-screw-terminal adaptors (included)
- Exceptional interference rejection
- Built-in transient protection and ground-lifting
- Compatible with qualified UTP cameras
- Includes rack mount hardware and eight NV-RJ45A adaptors
- Limited lifetime warranty
Employing NVT‘s latest generation DigitalEQ™ technology, the NV-3272 is an 32-channel active (amplified) hub that allows the transmission of full-motion monochrome or color video for distances up to 1 mile (1,6km) using Category 2 or better unshielded twisted-pair (UTP) wire. The receiver hub continuously and automatically conditions the video signal, compensating for cable attenuation, wiring polarity, ground loops, and voltage transients, independent of video signal content. The unparalleled interference rejection and low emissions allow long run video to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying “hum-bars” when ground-potential differences exist. With built-in transient protection, damaging voltage spikes are eliminated.
- Adaptive DigitalEQ™ fully automatic 4-band equalization provides adjustment-free equalization every time
- Compact rack-mountable 19” 1U high enclosure features 32 channels with 1 output per channel
- Full motion CCTV video at distances up to 3,000ft (1km) when used with any passive NVT transceiver or hub; 1 mile (1,6km) when used with the NV-653T active transmitter; 1,000ft (300m) with shielded twisted-pair when used with any passive NVT transceiver or hub
- RJ45 connectivity with optional NV-RJ45A RJ45-to-screw-terminal adaptors (included)
- Exceptional interference rejection
- Built-in transient protection and ground-lifting
- Automatic compensation for reverse-polarity wiring
- Frequency Response DC to 10 MHz
- At-a-glance per-channel diagnostics
- Compatible with qualified UTP cameras
- Includes thirty-two 2ft (60cm) coax jumper cables, rack mount hardware and eight NV-RJ45A adaptors
- Limited lifetime warranty
Order number: EMNVxxxx NVT NV-3242 32-Channel StubEQ™ Active Receiver Hub
Order number: EMNV3000 NVT NV-3272 32-Channel DigitalEQ™ Active Receiver Hub
